Dual-stack support with kubeadm

Your Kubernetes cluster includes dual-stack networking, which means that cluster networking lets you use either address family. In a cluster, the control plane can assign both an IPv4 address and an IPv6 address to a single Pod or a Service.

Before you begin

You need to have installed the kubeadm tool, following the steps from Installing kubeadm.

For each server that you want to use as a node, make sure it allows IPv6 forwarding.

Enable IPv6 packet forwarding

To check if IPv6 packet forwarding is enabled:

sysctl net.ipv6.conf.all.forwarding

If the output is net.ipv6.conf.all.forwarding = 1 it is already enabled. Otherwise it is not enabled yet.

To manually enable IPv6 packet forwarding:

# sysctl params required by setup, params persist across reboots
cat <<EOF | sudo tee -a /etc/sysctl.d/k8s.conf
net.ipv6.conf.all.forwarding = 1
EOF

# Apply sysctl params without reboot
sudo sysctl --system

You need to have an IPv4 and and IPv6 address range to use. Cluster operators typically use private address ranges for IPv4. For IPv6, a cluster operator typically chooses a global unicast address block from within 2000::/3, using a range that is assigned to the operator. You don't have to route the cluster's IP address ranges to the public internet.

The size of the IP address allocations should be suitable for the number of Pods and Services that you are planning to run.

Create a dual-stack cluster

To create a dual-stack cluster with kubeadm init you can pass command line arguments similar to the following example:

# These address ranges are examples
kubeadm init --pod-network-cidr=10.244.0.0/16,2001:db8:42:0::/56 --service-cidr=10.96.0.0/16,2001:db8:42:1::/112

To make things clearer, here is an example kubeadm configuration file kubeadm-config.yaml for the primary dual-stack control plane node.

---
apiVersion: kubeadm.k8s.io/v1beta4
kind: ClusterConfiguration
networking:
  podSubnet: 10.244.0.0/16,2001:db8:42:0::/56
  serviceSubnet: 10.96.0.0/16,2001:db8:42:1::/112
---
apiVersion: kubeadm.k8s.io/v1beta4
kind: InitConfiguration
localAPIEndpoint:
  advertiseAddress: "10.100.0.1"
  bindPort: 6443
nodeRegistration:
  kubeletExtraArgs:
  - name: "node-ip"
    value: "10.100.0.2,fd00:1:2:3::2"

advertiseAddress in InitConfiguration specifies the IP address that the API Server will advertise it is listening on. The value of advertiseAddress equals the --apiserver-advertise-address flag of kubeadm init.

Run kubeadm to initiate the dual-stack control plane node:

kubeadm init --config=kubeadm-config.yaml

The kube-controller-manager flags --node-cidr-mask-size-ipv4|--node-cidr-mask-size-ipv6 are set with default values. See configure IPv4/IPv6 dual stack.

Join a node to dual-stack cluster

Before joining a node, make sure that the node has IPv6 routable network interface and allows IPv6 forwarding.

Here is an example kubeadm configuration file kubeadm-config.yaml for joining a worker node to the cluster.

apiVersion: kubeadm.k8s.io/v1beta4
kind: JoinConfiguration
discovery:
  bootstrapToken:
    apiServerEndpoint: 10.100.0.1:6443
    token: "clvldh.vjjwg16ucnhp94qr"
    caCertHashes:
    - "sha256:a4863cde706cfc580a439f842cc65d5ef112b7b2be31628513a9881cf0d9fe0e"
    # change auth info above to match the actual token and CA certificate hash for your cluster
nodeRegistration:
  kubeletExtraArgs:
  - name: "node-ip"
    value: "10.100.0.2,fd00:1:2:3::3"

Also, here is an example kubeadm configuration file kubeadm-config.yaml for joining another control plane node to the cluster.

apiVersion: kubeadm.k8s.io/v1beta4
kind: JoinConfiguration
controlPlane:
  localAPIEndpoint:
    advertiseAddress: "10.100.0.2"
    bindPort: 6443
discovery:
  bootstrapToken:
    apiServerEndpoint: 10.100.0.1:6443
    token: "clvldh.vjjwg16ucnhp94qr"
    caCertHashes:
    - "sha256:a4863cde706cfc580a439f842cc65d5ef112b7b2be31628513a9881cf0d9fe0e"
    # change auth info above to match the actual token and CA certificate hash for your cluster
nodeRegistration:
  kubeletExtraArgs:
  - name: "node-ip"
    value: "10.100.0.2,fd00:1:2:3::4"

advertiseAddress in JoinConfiguration.controlPlane specifies the IP address that the API Server will advertise it is listening on. The value of advertiseAddress equals the --apiserver-advertise-address flag of kubeadm join.

kubeadm join --config=kubeadm-config.yaml

Create a single-stack cluster

To make things more clear, here is an example kubeadm configuration file kubeadm-config.yaml for the single-stack control plane node.

apiVersion: kubeadm.k8s.io/v1beta4
kind: ClusterConfiguration
networking:
  podSubnet: 10.244.0.0/16
  serviceSubnet: 10.96.0.0/16

What's next

• Validate IPv4/IPv6 dual-stack networking
• Read about Dual-stack cluster networking
• Learn more about the kubeadm configuration format